MOVIN TRACIN · MOVIN Studio Usage Guide
Streaming Mocap Data into SteamVR
Goal of this chapter: SteamVR sees your body as full-body trackers that line up with your headset and controllers.
The SteamVR target turns your actor into virtual trackers in SteamVR. Any SteamVR app that supports full-body trackers, such as VRChat or Resonite, can use them like regular trackers.
MOVIN Studio sends 8 body trackers:
| Tracker | SteamVR role |
|---|---|
| Hips | Waist |
| Chest | Chest |
| Left / right ankle | Left / Right Foot |
| Left / right knee | Left / Right Knee |
| Left / right elbow | Left / Right Elbow |
Your headset and controllers keep tracking your head and hands.
Before you start
- Windows. The SteamVR target is available only in MOVIN Studio for Windows.
- SteamVR is installed on the same PC as MOVIN Studio, and you've launched it once.
- A VR headset and both controllers are connected to SteamVR. The trackers are aligned to your headset, so a headset is required.
- An actor is selected, and no character is selected. SteamVR supports actor streaming only. See Create and Calibrate Actor.
- Free Basic License: SteamVR streaming works with the Basic License.
No separate driver to install. MOVIN Studio includes the MOVIN SteamVR driver and registers it for your Windows account automatically when it starts.
How to stream to SteamVR: Step by Step
-
Start SteamVR
- Start SteamVR and check that it tracks your headset and both controllers.
-
Select SteamVR and start streaming
- In the Streaming section of the bottom panel, click ⚙ to open the streaming settings.
- Set Platform to SteamVR. Host, Port Number and Additional Data are hidden - SteamVR always gets the body only, on the same PC.
- Click Stream. The status shows On, and SteamVR: connected once the driver answers.
If the status shows one of these messages, do what it says:
Message What to do Install SteamVR and launch it once to finish setup. Install SteamVR, launch it once, and wait - MOVIN Studio retries automatically. Restart SteamVR to load the MOVIN trackers. Close SteamVR and start it again. SteamVR setup failed. Retrying automatically... Wait. If it keeps failing, contact MOVIN with %LOCALAPPDATA%/MOVIN/SteamVR/setup.log.SteamVR cannot receive tracking data because port 39580 is in use. Close the app using that port, then restart SteamVR. -
Align SteamVR and MOVIN
While streaming to SteamVR, an Align button appears under the streaming status. Align lines up MOVIN's tracking space with SteamVR's, so the trackers sit on your body.
- Click Align. You have 10 seconds - a tone ticks each second.
- Put on your headset, hold both controllers, and stand in a T-pose inside the mocap zone. Keep still.
- Hold the T-pose until you hear the result tone. On success, the status shows Alignment complete. You can move normally now.
Run Align again after you recenter the headset, restart SteamVR, or move the MOVIN sensor.
-
Use the trackers in your app
- Start your SteamVR app and run its full-body calibration. For VRChat, see Streaming Mocap Data into VRChat.
If Align fails
The status tells you why. Fix the cause, then click Align again.
| Message starts with | What to do |
|---|---|
| Could not align. Make sure your Actor is being tracked... | Stand in the mocap zone so MOVIN Studio tracks your actor. |
| ...SteamVR could not track your headset. | Put the headset on and check its tracking in SteamVR. |
| ...MOVIN could not track your head and hands. | Make sure your whole body is visible to the MOVIN sensor. |
| ...your controllers did not line up with your hands in MOVIN. | Hold both controllers and stand in a T-pose. |
| ...SteamVR did not respond. | Check that SteamVR is running and the MOVIN driver is loaded (restart SteamVR). |
| Could not align. Press Align again, then keep still... | Keep still without turning or tilting your head during alignment. |
If an earlier alignment worked, it stays in use after a failed attempt.